**goHUNT staff recommends ordering this boot 1/2 size smaller than you would buy a Nike off the shelf.
*Please review our goHUNT staff boot profiles below and our sizing video before ordering.
goHUNT Staff Boot Profile
goHUNT Stiffness Scale Rating - Flex 4 (see stiffness tab)
The Tibet is built for the mountain hunter whose only focus is the animal they pursue without regard for the terrain that animal calls home
Trail loves the Tibet when in austere environments
I-Lock lacing cams allow you to separate the lace tension between the ankles and the tops of the feet for a better fit
Full, high-wall rubber rand resists abrasion
Lasted Gore-Tex lining provides waterproof/breathable protection against the elements
Warranty - Product defects and workmanship for 1 year from date of purchase
BreakdownThe Lowa Tibet is a long-time favorite among hardcore backcountry hunters. With a wider base, leather upper with a full rubber rand, and a GORE-TEX liner, the Tibet is ideal for carrying heavy loads over long distances in the nastiest terrain. The I-Lock lacing cams allow you to customize your boot fit by separating the lacing tension between the foot and ankle.
Don’t see the size you want? Email boots@goHUNT.com for any special requests.
HOW TO ACCURATELY MEASURE YOUR FEET TO FIND THE CORRECT BOOT SIZE
Start by collecting a few things from around your house, including a yardstick or ruler, a soft tailor’s tape or paper tape, a piece of cardboard or printer paper, and a pen.
Draw a 90° angle on the cardboard or paper using the yardstick or ruler. The lines should be long enough so that your longest toe touches the horizontal line and the widest point of your foot touches the vertical line.
Ensure that you’re wearing your hunting socks while taking these measurements. Stand on the paper or cardboard with your feet shoulder-width apart and place your full weight on both feet.
Have a second person mark where your heel and the widest part of your foot lands on the cardboard or paper. Ensure that you’re keeping the pen vertical when making your marks. Leaning the pen inward or outward against your foot will skew your measurements.
Place the edge of the tailor’s tape on the straight line and measure the widest and longest point of each foot down to 1/10th of a centimeter.
Add both length measurements together and divide them by two. This is your length measurement.
Add both width measurements together and divide them by two. This is your width measurement.
Record your measurements and refer to the goHUNT Sizing Guide and Staff Reviews to find the right boot size for your foot profile.
GENERAL TIPS TO ENSURE YOUR NEW BOOTS FIT PROPERLY
Measure your feet with the socks you intend to wear in the field.
Measure your feet later in the day. Your feet tend to swell slightly as the day progresses.
The arch and heel of your foot should feel snug but not tight. Your heel should feel secure in the heel pocket. If your heel lifts up when you step, make sure the lacing is not too loose.
Your toes should not touch the front of the boot. You want just enough room to wiggle your toes. When you kick the toe into the floor, you should know where the front of the boot is without your toes hitting.
If you're unable to cinch the boot tight enough to prevent heel slip or it allows your toes to touch the end of the boot, you will have a hard time with a heavy pack on steep downhill descents and you’ll want to size up.
goHUNT Return Policy If you should need to return a boot, they may be returned within 30 days of purchase for a full refund. Boots should be returned in brand new condition with no wear marks. All boots should be returned in the original packaging with the original tags. Boots must not be worn outside to be considered for a refund. We do not allow direct boot exchanges. If you return a product in brand new condition with all original packaging and tags, we will process your refund. You can order another product that best fits your needs or wait until your refund is processed. With all the backcountry hunters we have on staff at goHUNT, we understand the need and know how hard it is to find a boot that fits your foot. goHUNT has spent countless hours and measured many feet to make sure you get the right size boot the first time. If you watch our sizing video and review our staff foot profiles, we are extremely confident you'll find the right size boot for you the first time. In the rare case you don't, the goHUNT staff is on call to make sure you find the right boot for your next hunt.
*We're so confident in our extensive sizing research that if you fully review it, and correctly measure your foot, we know you'll find the boots that fit.
HOW DO I CARE FOR MY BOOTS?
Proper boot care can significantly extend the lifespan of your boots. Leather boots, in particular, need to be cared for after heavy use. If your boots are wet and covered in dirt, we recommend cleaning them. If you’re not going to clean your boots, you should still allow your boots to air dry after each use.
Remove your insoles and laces after each use. This will open up your boots and allow them to air out. Even if your boots don’t get wet, they will naturally absorb moisture from your feet, especially on multi-day trips. Insoles and laces can be hand-washed in cold water and set out to air dry.
Using a boot brush and warm water, remove the dirt from your boots. The warm water will open up the pores of the boot and allow you to thoroughly clean them.
For leather boots, you’ll want to recondition the leather after cleaning them with warm water in order for them to remain water-repellant. Applying a waterproofing agent to the damp leather will reclose the pores that were opened up during cleaning. Once you’ve reconditioned your boots, water should bead up when gently poured over the leather.
Allow your boots to air dry. Do not use a heat source to dry your boots. The heat could cause the leather to shrink or become brittle, increasing the chances of irreparable rips or creases.
Store your boots in a cool and dry place to prevent mildew. We recommend packing a newspaper in the toe box of wet boots to help absorb the moisture and maintain the boots’ shape during the drying process.
Take your boots to a knowledgeable cobbler for repairs.
WHAT SHOULD I USE TO TREAT MY NEW BOOTS?
For a general-purpose waterproofing product, the goHUNT staff has found that Granger or Nikwax Waterproofing performs the best.
Re-apply this product as necessary or after every use in severe conditions.
Please refrain from using beeswax, animal fats, or petroleum-based products on your boots, as these products will void some manufacturer warranties.
*Please note that these products may darken the color of any leather.
WHAT IF MY BOOTS ARE GORE-TEX®?
We recommend treating the leather on your Gore-Tex® boots the same as you would on any other leather boot.
The Gore-Tex® lining creates a waterproof/breathable membrane on the inside of the boot, but leather uppers still need to be cared for.
The durable waterproofness of the Gore-Tex® membrane is not affected by leather conditioners, silicone, oil, or shoe polish
This is a addition to my comments about the tibets the scarpa kenises pro gtx is a excellent boot to I think the tibrt's will last a long time as well
I got my tibets today ..delivery was fast the 10.5 wide fit good I will be keeping them! I have a old pair of kinesis pro gtx the tibets fit better I will write a review after I put a few hundred miles on. They are a beautiful and tough looking boot
This is without a doubt the finest boot that I have ever put my feet in.
I love these new boots! Took them out of the box and did a 20 mile backpacking trip same wknd. The extra room in the toe box will be great on my Elk hunt this yr with a little thicker sock. Had almost no issue doing the trip straight out of the box. The I-locks are one of the best features of any boot I've ever owned. Do not over tighten because they are truly locked down, you will be stopping on the trail to loosen them. I would buy these again in a heartbeat.
Lowa Tibet GTX
Forgot your password?
Don't have an account? Sign up now