Black Eagle Deep Impact F.O.C.O.S. Outsert System - 12 count

Name: Black Eagle Deep Impact F.O.C.O.S. Outsert System - 12 count
Brand: Black Eagle
SKU: BL-BI-000-1851-185-194
Price: 48.99 USD
Availability: InStock

PointsPoints

$48.99

% off Sold out

Material:

Aluminum Stainless Steel

Spine:

300 350 400

Product variants

Quantity

only 9 left in stock

The Black Eagle Arrows Deep Impact Front of Center Outsert System (F.O.C.O.S.) is designed to add more weight to the front end of the shaft, intended for use with Deep Impact arrow shafts.

Why we like this product

A perfect way to add F.O.C. to your Deep Impact arrow shaft builds
7075 T6 Aluminum alloy and Stainless Steel options
Designed for perfect alignment from shaft to insert/outsert to broadhead
Ultra-strong design
Easy to install

Breakdown

Black Eagle Arrows new Front of Center Outsert System (F.O.C.O.S.) is designed for those who want more weight up front and ease of use of outserts. The F.O.C.O.S. is made up of three components. The first is a black anodized 7075 T6 aluminum alloy outsert or the stainless steel option. Second, a stainless steel retention post (aluminum outsert option) or aluminum retention post (Stainless Steel option) also acts as a footer inside the shaft. Third, is the 3/32 Allen head retention screw that allows for the outserts to either be screwed or screwed and glued. Black Eagle tested this system up to 550 pounds per square inch of pulling power and the system stays on the shaft. If you are looking for maximum F.O.C. for maximum penetration and shot-after-shot performance, then the Deep Impact F.O.C.O.S. from Black Eagle is what you're looking for. Black Eagle Arrows recommends an insertion depth of the arrow into the outsert to be .610" approximately 5/8" with the outserts adding approximately 1.090" of length to the end of the arrow.

Black Eagle F.O.C.O.S. Install

Select the correct outsert for the right arrow shaft
Glue in Stainless steel/Aluminum retention post
Dry fitting is recommended on all components. Slide outserts over the shaft and spin test
If the outsert does not fit, that is ok. Use 100 grit sandpaper and lightly sand the shaft in a circular motion until the outsert fits snugly on the shaft. Start slowly and dry fit often so you don't remove too much of the arrow shaft
Note: You should have approximately 3/4" insertion when using Aluminum outserts
Wipe dust off the shaft with a clean paper towel (Cleaners are not recommended)
Again, spin test to ensure concentricity.
Use a silver or black sharpie and mark the shaft and outsert for perfect alignment
de outsert over the shaft and use a 3/32" retention screw and lock the outsert in place
If using glue, see the following steps
Black Eagle has tested their fletching glue, insert/outsert glue, and epoxy and they all work great
Apply an even amount of glue around the shaft to ensure you get enough glue in the grooves to hold
Slide outsert on a shaft rotating to make sure glue/epoxy is evenly dispersed
Use the 3/32" retention screw and lock the outsert in place
Once the outsert is glued on and the screw is installed stand the arrow on the nock end to dry

Weight	Aluminum Outsert Total - 80 grains (all spines) Stainless Steel Outserts Total - 100 grains (all spines)
Material	7075 T6 Aluminum alloy options Stainless Steel options
Compatible with	Deep Impact arrow shafts
Quantity	12 F.O.C.O.S. Outserts 12 F.O.C.O.S. Retention posts 12 F.O.C.O.S. Retention screws