Black Eagle Deep Impact F.O.C.O.S. Outsert System - 12 count





Regular price $48.99
Sale price $48.99 Regular price
% off Sold out

only 10 left in stock

The Black Eagle Arrows Deep Impact Front of Center Outsert System (F.O.C.O.S.) is designed to add more weight to the front end of the shaft, intended for use with Deep Impact arrow shafts.

Why we like this product
  • A perfect way to add F.O.C. to your Deep Impact arrow shaft builds
  • 7075 T6 Aluminum alloy and Stainless Steel options
  • Designed for perfect alignment from shaft to insert/outsert to broadhead 
  • Ultra-strong design
  • Easy to install

Black Eagle Arrows new Front of Center Outsert System (F.O.C.O.S.) is designed for those who want more weight up front and ease of use of outserts. The F.O.C.O.S. is made up of three components. The first is a black anodized 7075 T6 aluminum alloy outsert or the stainless steel option. Second, a stainless steel retention post (aluminum outsert option) or aluminum retention post (Stainless Steel option) also acts as a footer inside the shaft. Third, is the 3/32 Allen head retention screw that allows for the outserts to either be screwed or screwed and glued. Black Eagle tested this system up to 550 pounds per square inch of pulling power and the system stays on the shaft. If you are looking for maximum F.O.C. for maximum penetration and shot-after-shot performance, then the Deep Impact F.O.C.O.S. from Black Eagle is what you're looking for. Black Eagle Arrows recommends an insertion depth of the arrow into the outsert to be .610" approximately 5/8" with the outserts adding approximately 1.090" of length to the end of the arrow.

Black Eagle F.O.C.O.S. Install
  1. Select the correct outsert for the right arrow shaft
  2. Glue in Stainless steel/Aluminum retention post
  3. Dry fitting is recommended on all components. Slide outserts over the shaft and spin test
  4. If the outsert does not fit, that is ok. Use 100 grit sandpaper and lightly sand the shaft in a circular motion until the outsert fits snugly on the shaft. Start slowly and dry fit often so you don't remove too much of the arrow shaft
  5. Note: You should have approximately 3/4" insertion when using Aluminum outserts
  6. Wipe dust off the shaft with a clean paper towel (Cleaners are not recommended)
  7. Again, spin test to ensure concentricity. 
  8. Use a silver or black sharpie and mark the shaft and outsert for perfect alignment 
  9. de outsert over the shaft and use a 3/32" retention screw and lock the outsert in place
  10. If using glue, see the following steps
  11. Black Eagle has tested their fletching glue, insert/outsert glue, and epoxy and they all work great
  12. Apply an even amount of glue around the shaft to ensure you get enough glue in the grooves to hold
  13. Slide outsert on a shaft rotating to make sure glue/epoxy is evenly dispersed
  14. Use the 3/32" retention screw and lock the outsert in place
  15. Once the outsert is glued on and the screw is installed stand the arrow on the nock end to dry
Weight Aluminum Outsert Total - 80 grains (all spines)
Stainless Steel Outserts Total - 100 grains (all spines)
Material 7075 T6 Aluminum alloy options
Stainless Steel options
Compatible with Deep Impact arrow shafts
Quantity 12 F.O.C.O.S. Outserts
12 F.O.C.O.S. Retention posts
12 F.O.C.O.S. Retention screws 
Black Eagle

Black Eagle Deep Impact F.O.C.O.S. Outsert System - 12 count


Built by GOHUNT

Our latest must-have gear, perfect for use at home and in the field.

View all